Belkin F1UP002 User Manual

Wireless G All-In-One Print ServerF1UP002User Manual

10Installation ProcedureStep 1. Connecting Devices to your Print ServerBefore you start, you should have: • One computer with Windows 2000 SP4 or ab

1111sectionInstallation Procedure1234567891011Note: 1. You must use the power adapter shipped along with the Print Server; do NOT use any other power

12Installation Procedure 3. The Belkin All-In-One Print Server - InstallShield Wizard appears. Click “Next”.1234567891011section4. Click “Next” to i

1313Installation Procedure5. The system starts installing the Print-Server utilities.6. The “Server Configuration” screen will appear. To configure

14Installation Procedure The following steps are for Print-Server configuration upon choosing “Yes, I would like to configure my All-In-One Print Ser

1515Installation Procedure8. Enter the user name and password of the Print Server you have selected to log in. The default user name is “admin”; the

16Installation Procedure10. To set up the IP address of the Print Server, the default is set to “DHCP” for the TCP/IP configuration. The Print Serv

1717Installation Procedure If the DHCP server is unavailable or not found, the user will be prompted to configure the TCP/IP settings of the Print Se

18 The Print Server will check if the manually configured IP address in “TCP/IP Configuration” is in the same subnet as the connected computer runnin

1919Step 3. Configuring Wireless Settings1. The default wireless setting is “Auto” mode. The Print Server will detect a connection to a wired-LAN ne

Table of Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Product Features . . . .

203. If you choose to connect to an encrypted network, the “Wireless Security Settings” screen will appear. Select “Security Mode” and enter the secu

2121Note: If the Windows XP firewall in your system has been enabled, the Print Server will automatically open some necessary ports for the Print-Serv

22Installation ProcedureAt this point, disconnect the Ethernet cable between your Print Server and your router to enable the wireless functionality of

2323Installation ProcedureStep 4. Installing MFP Drivers/Utilities When the Print-Server installation is complete, the “Belkin All-In-One Print Manag

24Installation ProcedureTo connect the printer to your computer through the Print Server just like you have directly connected the printer to your com

2525Installation Procedure2. Windows will detect the new hardware and prompt to install the Print-Server drivers and then the printer drivers. When t

26Installation Procedure4.2 Printer drivers/utilities have been installed1. To bind the already-installed printer drivers/utilities with the Print S

2727Installation ProcedureDepending upon the previous configuration of your computer, duplicate system-tray icons or desktop shortcuts for scanners or

28Installation Procedure1234567891011sectionEnabling Auto-Timeout SettingsAfter the printer-driver installation is complete, check the “Auto release w

2929Installation ProcedureAdding New Client Computers to Print-Server SetupWhen adding a new client computer to share the print, scan, copy, fax, and

Table of ContentsGeneral Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XTCP/IP Configuration . . . . . . .

30Operating Print Server & Using the MFPsAfter you have followed the Installation Wizard to finish the printer installation, the printer is now co

3131Share ScanMost of the printers with built-in scanners provide a scan utility for users. You can scan pictures or documents through the utility. In

32Share Card ReaderIf your printer has built-in media-card readers, you can read the files from the plugged card reader through the Print Server.Windo

3333Fax a FileIf your printer has a fax function, you can fax files from your computer to the fax number you designated.An example: Fax through HP Off

343. The “Send Fax” screen appears. Configure the file and enter the fax number, and then click “Send Fax” to fax the file.Operating Print Server &am

3535Print Server ListThe Belkin All-In-One Print Manager can automatically find the Print Server in the network and show it in the Print Server List.

36Print Server ListThe Print Server List will show all the Print Servers within the network. You can find the Print Server’s information including “Al

3737Computer NameIt display the computer name of the user who is connecting to the printer.Contact InformationWhen the current user has set his “Conta

38My FavoriteYou can add the frequently used Print Servers to the “My Favorite” list. The Print Server in the list will be added to the quick-link lis

3939“My Favorite” List“ My Favorite” ListThe “My Favorite” list will show your favorite Print Servers. You can find the Print Server’s information inc

4IntroductionThank you for purchasing and using our Wireless G (the Print Server). This innovative product easily shares your standard printer or al

40To add the printer to the Auto Connect List, follow the steps below.1. Click “Add” from the Auto Connect List.All-In-One Print Manager1234567891011

41413. Select the printer that is connected to the selected Print Server. Click “OK”. Note that in some cases, new printing jobs cannot be printed be

42Quick SetupRight-click on the Print-Server icon in the system tray so you can see the Print Servers that you have designated to the “My Favorite” li

4343Quick SetupStatusThe current status of the printer will be displayed here. “Connected” indicates that you are connecting to the printer. “Busy” in

44General SettingStart Control Manager on Windows startupExecutes the Belkin All-In-One Print Manager when Windows starts every time. By default, it i

4545IntroductionThis chapter introduces the Print Server’s system-configuration utility in a Windows environment. This utility provides the most compl

46Search for Print ServersPrint Server Manager1234567891011sectionEvery time you run the “Server Manager” configuration utility, click the “Search” ic

4747Status of Print ServersPrint Server Manager1234567891011sectionClicking the “Status” icon on the tool bar will show the status of the currently se

48Set Up the All-In-One Print ServerPrint Server Manager1234567891011sectionClicking the “Setup” icon on the tool bar will show the selected Print S

4949General ConfigurationPrint Server Manager1234567891011sectionDouble-click the “General” icon and the “General” configuration window will appear. Y

55sectionIntroduction1234567891011Windows 98SE/Me/NTLPRMFP / Print serverLinuxLPRWindows XP/2000Click “connect” or IPP or LPRPrinterORAll-in-one Print

50TCP/IP ConfigurationPrint Server Manager1234567891011sectionDouble-click the “TCP/IP” icon and the “TCP/IP” configuration window opens. You can conf

5151IP SettingsClick the “IP” button to enter the IP-setting page. By default, “Auto IP” is selected to enable the Print Server to automatically get a

52If the DHCP server is unavailable or not found, the user will be prompted to configure the TCP/IP settings of the Print Server manually by clicking

5353The Print Server will check if the manually configured IP address is in the same subnet as the network or connected computer. If the TCP/IP-addres

54If the DHCP server is enabled, you have to assign a valid range of IP addresses. Fill in the “Starting Address”, “Range”, “Subnet Mask”, “Gateway”,

5555Print Server Manager1234567891011sectionSystem ConfigurationDouble-click the “System” icon and the “System” configuration window pops up.In the Sy

56Wireless Function: You can select to enable or disable the wireless function manually. If you manually enable wireless function, the Print Server’s

5757Print Server Manager1234567891011sectionThe default settings of the Print-Server wireless function are as follows:• Mode: Infrastructure• SSID:

58Infrastructure Mode:Print Server Manager1234567891011sectionIn the Infrastructure mode, you have to allow the Print Server to associate with an acce

5959Print Server Manager1234567891011sectionIn the Ad-Hoc mode, you can allow the Print Server to automatically associate with another wireless statio

6IntroductionPS (Print-Server) ModeThe Print Server also supports LPR, IPP, and RAW printing protocols, which enable users to share the print function

60Print Server Manager1234567891011sectionBoth Infrastructure and Ad-Hoc modes have to go through the following procedure:This Print Server supports W

6161Print Server Manager1234567891011sectionWPA-PSK, you have to select “WPA-shared key” or “WPA-None” specified for Ad-Hoc mode. The wireless-securit

62

6363

© 2004 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Apple, AirPort, Mac, Mac

77sectionGetting to Know your Print Server 1234567891011LEDsThe Print Server features three LEDs that provide information about a) your wireless conne

8Getting to Know your Print Server Reset ButtonReset (Press the “Reset” button with a pencil tip for less than 5 seconds)• While the Reset button is

99sectionPlacement of the Print Server1234567891011The Print Server can be placed on a flat surface or mounted on an MFP or standard printer.Placement