Belkin F6C625-220V User Manual download pdf

The computer interface port has the following characteristics:

1. Plug-and-Play Support

2. Hot-Attachment

3. USB Port Protection

4. Self-Powered

5. 1.5 Mbps Low-Speed

USB Device

6. Compliant with USB

Specification Version 1.0

7. Compliant with HID Specification Version 1.0

8. Compliant with HID Power Device Class Version 1.0

9. Display UPS Status Data:

Voltage Out-of-Range/Buck/Boost/Frequency Out-of-Range/Overload Over

Charged/Over Temperature/Internal Fail/Shutdown Request/Shutdown

Imminent Switch On/Off/Switchable/Tested Awaiting

Power/Good/Beeper/Terminate Charge Terminate Discharge/Below

Remaining Capacity-Limit/Remaining Time Limit-Expired

Charging/Discharging/Fully Discharged/Need Replacement

10. Measurement Items:

AC Input Voltage/AC Output Voltage/AC Input Frequency/AC Output

Frequency Battery Voltage/Battery Capacity/Temperature Percent Load

11. Control Items:

Turn On/Off Outlet/Schedule Shutdown/High/Low Transfer Voltage/Battery

Test Delay Before Shutdown/Delay Before Startup/Delay Before Reboot

4.0 Inspection

Inspect the UPS upon receipt. The packaging is recyclable; save it for

reuse or dispose of it properly.

4.1 Placement

Install the UPS in a protected area with adequate air flow and free of

excessive dust. Do not operate the UPS where the temperature and

humidity are beyond the specified limits.

4.2 Connect Computer Interface

Belkin Sentry Bulldog Shutdown Management Software and the USB or

RS232 DB9 cable (depending on model) can be used with this UPS. If

used, connect the interface cable to the computer interface port on the back

panel of the UPS and then connect to the USB or Serial port on your PC.

4.3 Connect to Utility

Connect the AC input power connector to utility power to power up the

UPS.

4.4 Charge the Battery

The UPS charges its battery whenever it is connected to the utility power.

For best results, charge the battery for 4 hours prior to initial use.

4.5 Connect the Loads

Plug the loads into the output connectors on the rear of the UPS. To use the

UPS as a master on/off switch, make sure all of the loads are switched on.

4.6 Cable Management

It is used to corral all of the power cords into a neat and safe order. It also

assists in preventing accidental cord detachment.

UPS Uninterruptible Power Supply User Manual

Thank you for purchasing the Belkin Uninterruptible Power Supply (UPS). It will

provide you with the best protection for your connected equipment.

Please read this manual!

This manual provides safety, installation, and operating instructions that will help

you obtain the highest performance and service life that the UPS has to offer.

Please save this manual!

It includes important instructions for the safe use of this UPS and for obtaining

factory service should the proper operation of the UPS come into question.

Please save or recycle the packaging materials!

The UPS shipping materials were designed with great care to provide protection

from transportation-related damage. These materials are invaluable if you ever have

to return the UPS for service. Damage sustained during transit is not covered

under the warranty.

Responsible Party:

Important Safety Instructions

Have you ever noticed your lights dim or flicker when you turn on your

dishwasher or air-conditioning? This common occurrence is attributed to an

under-voltage of power, also known as a BROWNOUT.

A brownout is a period of insufficient power-line voltage. It is the most common

power problem, accounting for 80% of all power disturbances.

Effects: A brownout can deprive a computer of the power it needs to function,

causing unwanted damage to your computer, such as frozen keyboards and hard

drive crashes. Such problems will cause you to incur computer repairs, lost data,

and downtime.

Solution: A Belkin Uninterruptible Power Supply (UPS) with Automatic Voltage

Regulation (AVR). Typical "Stand-by" UPS units do not have AVR to increase the

output voltage or decrease the output voltage to your computer. A surge

protector can only protect your computer from over-voltages due to irregular

power. Belkin UPS units protect against surges, spikes, swells, line-noise,

brownouts, and blackouts!

Only a Belkin UPS with AVR can give your computer clean

and consistent power at all times.

Note: There is no guarantee that interference to radio/TV will not occur in a

particular installation. If this UPS causes interference to radio or television

reception (this can be determined by turning the UPS power off and on), the user

is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

• Increase the separation between the equipment and the receiver.

• Reorient or relocate the receiving antenna.

Introduction

CAUTION!

To reduce the risk of electric shock, disconnect the UPS from

the main power supply before installing a computer interface signal cable.

Reconnect the power cord only after signaling interconnections have been made.

CAUTION! The internal energy source (the battery) cannot be

de-energized by the user. The output may be energized when the unit is not

connected to a main power supply, thus, a shock hazard may be present.

CAUTION! (RISK OF ELECTRIC SHOCK) HAZARDOUS LIVE PARTS

INSIDE THIS UNIT ARE ENERGIZED FROM THE BATTERY SUPPLY EVEN WHEN

THE INPUT AC POWER IS NOT CONNECTED.

CAUTION! (RISK OF ELECTRIC SHOCK) DO NOT REMOVE COVER. NO

USER SERVICEABLE PARTS INSIDE, PLEASE REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE, ONLY REPLACE THE

FUSE WITH THE SAME TYPE AND RATING.

Safety

Presentation

FRONT PANEL

Different LEDs on the front panel will signal information when various

conditions occur:

LED

: Light

: Flash

MEANING

3.0 ON-LINE Green

Utility is normal.

Utility is abnormal—AVR (Automatic Voltage

Regulation) in operation.

3.1 ON-BATTERY Yellow

UPS supplies power to outlets from

battery source.

Battery is low; the UPS will start shutdown.

The buzzer sounds an audible alarm.

3.2 OVERLOAD Red

There is a problem with the UPS. The LED will be lit

continuously and the buzzer will sound an audible

alarm for 10 seconds.

Battery output is drawing more power than the UPS

can provide.

3.3 REPLACE BATTERY Red

Battery is too weak or bad.

If UPS is in “On-Battery” mode this means the UPS is

just testing the condition of the battery.

3.4 ON/OFF/TEST/SILENCE BUTTON

Press the button more than 3 seconds to turn the UPS on or off, press the

button less than 3 seconds to activate the UPS self-testing or to silence

the back-up alarm.

REAR PANEL

3.5 INTERFACE PORT

Provides both USB or RS232 (depending on model) to relay the signal to

support DOS

, Windows

, and other operating systems.

3.4 On/Off/Test/Silence

3.0 On-Line

3.1 On-Battery

3.2 Overload

3.3 Replace

Battery

REAR PANEL (continued)

3.6 TELEPHONE/FAX/MODEM OR 10Base-T NETWORK PROTECTION

Telephone/Fax/Modem lines are surge protected and provide complete

safety for Internet connection. One input and two outputs allow for two

devices to be protected (i.e. modem and fax).

3.7 BATTERY REPLACE DOOR (HOT-SWAPPABLE)

3.8 SITE WIRING FAULT INDICATOR

The Site Wiring Fault LED will illuminate when one of the following

conditions exist:

1. Open or high-resistance ground

2. Hot and neutral polarity reversal

3. Overloaded neutral circuit

3.9 AC INPUT POWER RECEPTACLE

3.10 AC BREAKER (CIRCUIT BREAKER)

The circuit breaker button will stick out if an overload condition forces the

UPS to disconnect itself from utility power. If the button sticks out,

disconnect non-essential equipment.

3.11 BATTERY BACK-UP OUTLET

Data-sensitive equipment, such as a computer, monitor, and external drive

should be powered by these outlets. Battery power is automatically

provided in case of a power outage. Power (utility or battery) is not

supplied to these outlets when the UPS is switched off. (Do not plug surge

protectors or power strips into the battery back-up outlets.)

3.12 SURGE-ONLY PROTECTED OUTLETS

Equipment such as a printer, fax machine, scanner, or desk lamp should

be powered by these outlets. These outlets do not provide power during a

power outage. These outlets are always on (when utility power is available)

and are not controlled by the front panel switches.

Note: During the self-test, the UPS briefly operates the loads on-battery (the on-

battery LED comes on). If the UPS passes the self-test, it returns to on-

line operation.

The on-battery LED goes off and the on-line LED goes on steady. If the

UPS fails the self-test, it immediately returns to on-line operation and

lights the “REPLACE BATTERY” LED. The loads are not affected. Recharge

the battery overnight and perform the self-test again. If the “REPLACE

BATTERY” LED is still on, the battery will need to be replaced.

5.3 SILENCE

In " BACK-UP" mode, push on/off/test less than 3 seconds to silence the audible

alarm. (The function is void when under condition of "LOW BATTERY" or

"OVERLOAD".)

Note: In back-up mode, the UPS can be automatically turned off if none of the

connected loads are operating.

Operation (continued)

Alarm

6.0 BACK-UP (slow alarm)

When in "BACK-UP" mode, the yellow LED illuminates and the UPS sounds

an audible alarm. The alarm stops when the UPS returns to “LINE

NORMAL” operation.

6.1 LOW BATTERY (rapid alarm)

In "BACK-UP" mode, when the battery energy runs low, the UPS beeps

rapidly until the UPS shuts down from a depleted battery or returns to

“LINE NORMAL” operation.

6.2 OVERLOAD (continuous alarm)

When the UPS is overloaded (the connected loads exceed the maximum

rated capacity), the UPS emits a continuous alarm to warn of an overload

condition. Disconnect nonessential equipment from the UPS to eliminate

the overload.

6.3 FAULT (30 seconds continuously)

When the output is shorted, the UPS emits a 30-second continuous alarm

to warn of a short condition.

Disconnect the equipment from the UPS prior to checking the

equipment.

Software Options

7.0 Belkin Sentry Bulldog Shutdown Management Software

Belkin Sentry Bulldog Shutdown Management Software receives

communication through the USB or RS232 interface port (depending on

model) to perform monitoring functions, and also provide an orderly

shutdown of the computer in the event of a power failure. Moreover, Belkin

Sentry Bulldog Shutdown Management Software displays all of the

diagnostic symptoms on screen, such as Voltage level, Frequency, Battery

level, etc.

The software is available for Windows

95, Windows

98, Windows NT

V4 or higher, and Windows

2000.

7.1 Interface Kits

Each interface kit includes a special interface cable which is required to

convert status signals from the UPS into signals that the individual

operating system can recognize. The interface cable must be connected to

the USB or RS232 port (depending on model) on the UPS. The other side

of the interface cable can be connected to the USB or RS232 port

(depending on model) of your PC. For other installation instructions and

features, please refer to the README file.

CAUTION:

Use only a factory supplied or authorized UPS monitoring cable!

7.2 USB (Universal Serial Bus): HID (Human Interface Device)

setup procedure

1. When the USB cable that comes with the UPS is first connected to a

USB port on your computer, the Windows

98 dialog called “ADD NEW

HARDWARE WIZARD” should appear automatically.

(To display this dialog manually, you can choose the Start button and then

“Settings” to access the Control Panel and then double-click “ADD NEW

HARDWARE”. The USB cable should be connected already.)

2. The “ADD NEW HARDWARE WIZARD” dialog box guides you through

the installation process. Click “Next”.

3. A dialog states "Windows will now search for any new Plug-and-Play

devices on your system". Click “Next”.

4. A subsequent dialog gives you these options:

• Search for the best driver for your device (recommended).

• Display a list of all drivers in specific location, so you can select

the driver you want.

Please accept the recommended choice by clicking “Next”.

5. The Wizard will then search your hard drive for a file

called….\INF\hiddev.inf. This file contains all the information that

Windows

98 needs to install the correct device drivers.

6. At this point the wizard might ask for the Windows

98 CD-ROM.

Place the CD in the CD-ROM drive and select “OK”.

7. The installation process will continue automatically until a dialog

displays indicating that the drivers have been installed. Select the

“Finish” button and your drivers are installed.

USB Interface Port

P73446-B

Belkin Components, Ltd.

Unit 13 • Gatelodge Close • Round Spinney

Northampton • Northants • NN3 8RX

United Kingdom

Tel: +44 (0) 1604678300

Fax: +44 (0) 1604678330

Belkin Components B.V.

Diamantlaan 8 • 2132 WV

Hoofddorp • The Netherlands

Tel: +31 (0) 235698765

Fax: +31 (0) 235612694

Presentation (continued)

CAUTION:

Never connect a laser printer or scanner to the

backup outlets of the UPS with other computer equipment. A laser

printer or scanner periodically draws significantly more power when

in use than when idle. This may overload the UPS.

Installation

4.7 Connect the Telephone/Fax/Modem Lines

Connect a single-line telephone/fax/modem line into the surge-protected

sockets on the back of the UPS. The RJ45/RJ11 modular sockets accept

standard single-line telephone connections. This connection will require

another length of telephone cable (supplied).

Note: This connection is optional but highly suggested as telephone/fax/modem

lines often carry dangerous surges and spikes. The UPS works properly

without a telephone/fax/modem connection.

CAUTION: The telephone/fax/modem protection feature could

be rendered inoperable if improperly installed. Make sure that the

telephone line from the wall is plugged into the connector marked

"IN", and the device to be protected (telephone/fax/modem) is

plugged into the connector marked "OUT".

CAUTION: This surge-protection device is for indoor use only.

Never install telephone wiring during a lightning storm.

5.0 Switch On

With the UPS plugged in, press and hold the on/off/test/silence button for more

than 3 seconds until the "ON-LINE" LED lights up to switch the UPS on.

The UPS will perform self-testing each time it is switched on.

Note: The UPS maintains the battery charge when in the off position and will

respond to commands received through the computer interface port.

5.1 Switch Off

Press and hold the on/off/test/silence button for more than 3 seconds until the

"ON-LINE" or "ON-BATTERY" LED goes off.

5.2 SELF-TEST

Use the self-test to verify both the operation of the UPS and the condition of the

battery. In normal utility power, push the on/off/test/silence button less than 1

second and the UPS performs a self-test function. During the self-test, the UPS

operates in back-up mode.

Operation

1 2

P73446-B 1
P73446-B • 2

Summary of Contents

Page 1 - P73446-B

The computer interface port has the following characteristics:1. Plug-and-Play Support2. Hot-Attachment3. USB Port Protection4. Self-Powered5. 1.5 Mbp

Page 2 - P73446-B •

1. Firmware Version of Firmware2. Rating VA Rated Power Capacity of UPS3. Rating Voltage Rated Power Voltage of UPS4. Rating Frequency Connected Frequ